Sanding Kitchen Cabinets Before Paint: Grits, Deglosser and How Far to Go

As an Amazon Associate I earn from qualifying purchases.
All claims are strictly my personal opinion.

My top pick

Bosch ROS20VSC 5-Inch Random Orbit Sander

Bosch ROS20VSC 5-Inch Random Orbit Sander

Variable speed from 7,500 to 12,000 OPM suits a light scuff on flat doors and frames, with on-board dust filtering.

Sanding kitchen cabinets before paint with a sanding sponge and a palm sander

Sanding kitchen cabinets before paint doesn’t mean going down to bare wood: you clean off the grease, then scuff the old finish until the shine is gone, and that is the whole job. A fine grit in the 180 to 220 range is the usual scuff, a coarser one only comes out for repairs or old finish you want gone, and a very fine one goes between coats. On profiled doors a liquid deglosser or a sanding sponge can do what a sander can’t.

Below is how far to sand, which grit to use at each stage, the order of the steps, how to handle raised panels and corners, what to do between primer and paint coats, how to keep the dust out of the rest of the house, and the tools I’d reach for.

⚡ Quick Answer

Flat doors and frames: degrease, then scuff with 180 to 220 grit. A 5-inch random orbit sander or a 1/4-sheet sander does it quickly.

Profiles and corners: use a sanding sponge or a detail sander, or a deglosser where sanding is slow.

Between coats: a very fine grit, 320 and up, only to knock down bumps and dust.

Do You Have to Sand Kitchen Cabinets Before Painting?

Paint grips a surface that has some tooth, and old cabinet finishes are usually glossy and slick. That is why every cabinet-painting guide I read has a prep step that dulls the finish. The question is only how that step gets done. Sherwin-Williams, in its own cabinet sanding guide, says it’s best to use a deglosser rather than sand through your cabinet finish. In other words, the target is a dull, even surface, not a trip down to the wood.

Scuff Sanding Is Enough on Sound Finishes

If the existing finish is intact (no peeling, no chips, no sticky areas), scuff sanding is the whole sanding job. Sherwin-Williams’ professional cabinet refinishing guide describes scuff sanding as creating a surface profile that helps the primer adhere. You are not trying to remove the finish. You are trying to take the gloss off every square inch, which you can see: a scuffed surface looks uniformly dull, and any shiny patch left behind is a spot you missed.

When a Deglosser or Bonding Primer Can Stand In

A liquid deglosser, often sold as liquid sandpaper, cleans and dulls a sound finish chemically and makes no dust. It works on the flat panels and, more usefully, on moldings and raised panels where sanding is slow. My guide to liquid sandpaper covers what it can and can’t do, including why it has no grit equivalent. Use the product’s own directions, because wait times differ by brand.

A bonding primer is a separate decision. Some people paint cabinets with only a deglosser and a bonding primer and skip the sandpaper. That can work on a sound, clean finish, but it leaves you nothing to check by eye, and it doesn’t flatten a drip or a chip. If you’re unsure what the old finish is, or it’s glossy, I’d still scuff the flat areas and use the deglosser on the profiles. Do both, and the guesswork goes away.

When You Do Need to Sand Harder

Peeling or chipped paint, drips, rough patches, filler and wood that has been stripped all need an abrasive, because only an abrasive can level a surface. If the cabinets have a plastic or thermofoil skin, check the primer maker’s directions before sanding, since those surfaces behave differently from wood. If you aren’t sure whether to repaint or restain, my guide to refinishing kitchen cabinets walks through that choice and the whole process from start to finish.

Grits by Stage

The grit ranges below follow Sherwin-Williams’ cabinet sanding guide, which pairs coarse grits with removing finish, medium grits with raw wood, fine grits with prep before paint, and extra fine grits with buffing between coats. Where I add a number of my own, such as 120 for repairs, I say so. If you want the numbering explained, see the sandpaper grit chart and the grit guide for wood.

Stage Grit What it is for
Scuff sanding before primer 180 to 220 Dulls a sound finish so primer can grip; Sherwin-Williams’ fine range for prep before paint
Repairs and rough spots About 120 Levels chips, dried drips and filler; follow with 180 to 220 so the scratches don’t show. Sherwin-Williams gives 100 to 150 for medium work on raw wood
Removing old finish 40 to 80 Only if you are going to stain; too coarse for a paint job and it leaves deep scratches
Between primer and paint coats 320 and finer Gently buffs away bumps and dust between coats

⚠️ Important

Don’t go coarser than you need. A deep scratch from a 40 or 60 grit pass shows up under paint, and on veneer you can sand straight through the surface layer. On veneer, stay with light strokes. When in doubt, go finer and slower.

Step by Step

  1. Take everything off. Remove doors, drawers and hardware, and label each door and its position so it goes back where it came from. Sherwin-Williams suggests a drill to remove hardware quickly without stripping screws.
  2. Degrease before you sand. Kitchen cabinets carry food splatter and oil, and Sherwin-Williams says that residue needs to be cleaned before you start sanding. Sanding over grease drives it into the scratches. Start with dish soap and warm water on a microfiber rag; for stubborn grime, Sherwin-Williams recommends a stronger solution like TSP, used in a well-ventilated area.
  3. Let everything dry, then fix problems first: fill dents and gouges, let the filler cure, and sand it level. My roundup of the best wood filler covers what to use.
  4. Scuff the flat surfaces. Use light, steady pressure and keep the pad flat so you don’t dig in. Sand with the grain and work in small sections. Keep pressure even to avoid unwanted dips and curves.
  5. Do the profiles and corners by hand (more on that in the next section).
  6. Clean off the dust. Vacuum, then wipe with a tack cloth. Sherwin-Williams points out that a bleached tack cloth needs no water, so there’s no drying time before painting.
  7. Prime, then sand lightly between coats as described below.

Doors, Frames and Boxes

Do the doors first, on a pair of sawhorses or a bench, one face at a time. The boxes and face frames on the wall are the same job on a vertical surface: scuff with a sponge or a sander held lightly. If the box is veneer, use gentle strokes and finer paper, because you can cut through it quickly. Don’t sand the inside of the boxes unless you’re painting them.

Profiled Doors and Corners

Shaker and raised-panel doors have inside corners, rails and beads that a flat pad never touches. Sherwin-Williams’ own advice is to keep sheets in several grits for cabinet contours and corners, and to use sheets for contoured areas even when you have an orbital sander. A sponge is the easiest way to follow them, because it bends around a curve and doesn’t dig in at the edge. A detail sander gets into square corners where your finger or a sponge won’t.

Sanding Sponges

Fold a fine sponge into the groove and pull it along the profile with the grain. A sponge is gentler than paper on edges, so you’re less likely to round over a crisp edge. You can use it dry for the scuff and slightly damp for wiping the dust after, although I’d check the maker’s directions before getting any cabinet wet.

Detail Sanders

A detail sander has a small pointed pad that fits into corners and along narrow rails. It is slow on large areas, so it is a partner to your main sander, not a replacement. For help choosing between sander types for small, shaped work, my guide to the best sanders for furniture refinishing compares them.

A Deglosser Where Sanding Is Slow

On a heavily profiled door, a deglosser on a rag reaches into grooves that a sponge can’t. This is the classic place to use it, and it is why many painters combine both: sponge or sander on the flats, deglosser on the details. See liquid sandpaper for the details and the cautions.

Sanding Between Primer and Paint Coats

The scuff before primer and the sanding between coats are two different jobs with two different grits. After the primer dries, Sherwin-Williams’ professional guidance is to use a very fine abrasive to remove bumps and dust before the finish coat, because any imperfection you leave is magnified by the topcoat. So after the primer, and again after the first paint coat if the finish isn’t smooth, use 320 grit or finer: the goal is to knock off nibs and raised grain, not to cut through the coat.

  • Wait for the coat to dry as the can says. Sanding a soft coat gums up the paper and drags the paint.
  • Use a very light touch. You are polishing off bumps. If you see the old finish or bare wood, you’ve gone too far on that spot.
  • Wipe the dust off completely with a tack cloth or a clean microfiber before the next coat.
  • Sponges work well here, because they don’t dig in at edges, where the paint is thinnest.

If you’re planning to spray the cabinets, the same between-coat routine applies, and the sprayer choice matters more than the sander. My guide to the best paint sprayer for cabinets goes through it.

Dust Control in a Kitchen

Dust is the part of this job that follows you around the house, and the finer the grit, the finer and further the dust travels. A few habits help.

  • Sand outside or in a garage if you can. Doors come off, so most of the sanding doesn’t have to happen in the kitchen.
  • Connect the sander to a vacuum if it has a dust port. The DEWALT page, for instance, lists a locking dust-port system for a vacuum hose, and the Bosch page lists on-board filtering for fine dust.
  • Seal the room: tape plastic over doorways and vents, and close the cabinet boxes you’re not working on.
  • Vacuum before you wipe. A tack cloth picks up dust the vacuum leaves behind, but it clogs fast if the surface is covered in it. Sherwin-Williams also recommends vacuuming the work area so stray particles don’t land in wet paint.
  • Wear a respirator or a dust mask rated for fine dust, and eye protection.

If you don’t want to price all this out, the cabinet refinishing cost calculator compares doing the job yourself against hiring it out.

The Tools I’d Use

The specs below come from the makers’ own product pages, which I opened on November 20, 2026. Where a page doesn’t say something, I write that it’s not stated. I don’t show prices or customer ratings, which change daily.

Bosch ROS20VSC 5-Inch Random Orbit Sander

Bosch ROS20VSC 5 inch random orbit sander for sanding kitchen cabinet doors

Best for Flat Doors and Frames

Sherwin-Williams recommends an orbital sander over hand sanding for the flat panels, and this is the one I’d pick for them. Bosch lists a 2.5 amp motor, a speed range adjustable between 7,500 and 12,000 OPM, a 5-inch pad and disc, a pad dampening brake system meant to help prevent swirl marks, and on-board dust filtering. The low end of the speed range suits a light scuff.

Check price on Amazon

  • ✅ Variable speed, so you can go gentle
  • ✅ Dust filtering on board
  • ✅ Hook-and-loop discs change fast
  • ❌ Round pad doesn’t reach square corners

Best For: Scuffing flat doors, drawer fronts and face frames.


DEWALT DWE6411K 1/4-Sheet Palm Sander

DEWALT DWE6411K quarter sheet palm sander for cabinet doors and corners

Best for Square Corners and Rails

A square pad reaches the inside corners of a frame and the ends of rails that a round pad can’t. DEWALT lists a 2.3 amp motor delivering 14,000 OPM, a foam pad, a sanding plate of 4.5 x 5.5 inches, a paper clamp, a paper punch in the kit, a locking dust bag, and a locking dust-port system for a vacuum hose. The page doesn’t say which sandpaper grits come in the box.

Check price on Amazon

  • ✅ Square pad for corners
  • ✅ Vacuum port plus a dust bag
  • ✅ Rubber overmold grip
  • ❌ Needs sheets cut or punched to size

Best For: Frames, rails and anyone who wants a single sander for the whole job.


BLACK+DECKER BDEMS600 Mouse Detail Sander

BLACK+DECKER BDEMS600 mouse detail sander for cabinet corners and profiles

Best for Corners and Profiles

For the spots a bigger sander can’t enter, this detail sander is the one I’d choose. Black+Decker’s page lists a 1.2 amp motor, a detail pad for odd and awkward angles, an included finger attachment for tight spots, and a dust canister. It is for small areas, not whole doors.

Check price on Amazon

  • ✅ Reaches tight corners
  • ✅ Finger attachment included
  • ✅ Dust canister
  • ❌ Too small for flat panels

Best For: Inside corners, beads and narrow rails on profiled doors.


3M SandBlaster Dual Angle Sanding Sponge

3M SandBlaster dual angle sanding sponge for cabinet profiles and corners

Best Sponge for Edges and Grooves

The dual-angle shape is made for getting into corners and along profiles, which is where a flat block fails. The listing linked here is the 180-grit version, the low end of the fine range for scuffing. It is a sensible companion to a sander on any raised-panel door.

Check price on Amazon

  • ✅ Follows profiles and corners
  • ✅ No power cord, no dust port to manage
  • ❌ 180 grit is too coarse for sanding between coats

Best For: Grooves, beads and corners on shaker and raised-panel doors.


3M Sanding Sponges

3M sanding sponges for scuffing and sanding between coats on cabinets

Best for Scuffing and Between Coats by Hand

Sherwin-Williams’ own cabinet guide names a 3M sanding block sponge for hand sanding. A sponge is the gentlest way to scuff veneer and the least risky between coats, because it bends instead of digging in. The pack linked here is 3M’s Pro Grade Precision 3-in-1 sponge in 220 grit, fine, a 4-pack, which sits at the fine end of the scuffing range; for between coats, pick a finer sponge or 320 paper.

Check price on Amazon

  • ✅ Gentle on edges and veneer
  • ✅ Easy to hold and to fold into grooves
  • ❌ Slower than a sander on large panels

Best For: Hand scuffing, veneer boxes and sanding between coats.


How I Put This Guide Together

The grit ranges, the degreasing advice, the notes on profiles and the dust steps come from Sherwin-Williams’ cabinet sanding guide and its professional cabinet refinishing guide, plus the search results people see for this question. The tool specs come from the Bosch, DEWALT and Black+Decker product pages. Where a page didn’t state something, I say so. More on how I choose the products I recommend.

🏆 The Verdict

Degrease, scuff with 180 to 220 grit until the gloss is gone, handle profiles with sponges or a deglosser, and sand lightly with 320 or finer between primer and paint. A Bosch ROS20VSC covers the flat parts, and a 3M sanding sponge covers the rest.

❓ Frequently Asked Questions

Do you have to sand your cabinets before painting?+
You have to dull the finish, and sanding is the most reliable way to do it. A light scuff with a fine grit, around 180 to 220, is usually enough on sound cabinets. A deglosser is the other route: Sherwin-Williams says it’s best to use one rather than sand through your cabinet finish. Peeling, chipped or rough areas still need sanding.
Can I just paint over my kitchen cabinets without sanding?+
Only if you replace the sanding with something else: clean off the grease, take the gloss off with a deglosser, and use a bonding primer. Painting straight over a glossy, greasy finish is the usual reason cabinet paint peels. If you can’t see an even dull surface after prep, sand the spots that are still shiny.
What can I use if I don’t have a sander?+
Sanding sponges and sandpaper wrapped around a block work fine for scuffing, and a sponge is the better tool for profiles. Sherwin-Williams lists a sanding sponge for hand sanding, and a liquid deglosser on a rag handles grooves without any dust. Hand sanding is slower on big flat doors, but it is entirely doable.
What grit sandpaper for cabinets between coats?+
Use an extra fine grit, 320 and up. Sherwin-Williams says 320 and finer will gently buff away any bumps between paint or staining coats. Let the coat dry fully, sand lightly, then wipe off all the dust before you recoat.

Conclusion

Sanding cabinets for paint is a prep job, not a stripping job: clean, scuff until dull, repair what is damaged, and sand lightly between coats. Keep a sander for the flat parts and sponges or a detail tool for the rest, and keep the dust where it started. For the full paint-or-restain process, my guide to refinishing kitchen cabinets picks up where this one stops.

Get new sanding guides and seasonal deals roundups by email, about once a month.

About James Draper

Expert craftsman and passionate about teaching others the art of renewing items by sanding.
Bookmark the permalink.

Leave a Reply

Your email address will not be published. Required fields are marked *